Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： 1Cutting edge wear and burr measurement On the spot, it is customary to determine the burr size of the punching piece and determine the grinding time by hand，Excessive error。Of course，The degree of edge wear and edge bluntness can only be detected by detecting the burr height and thickness of the punch、Burr distribution uniformity、Punching size, shape and position accuracy and punching surface quality，Master cutting edge wear、The degree of sharpening of the cutting edge，Determine the timing of sharpening。 Generally, the burr height of the punch can be measured with a micrometer。To improve the measurement accuracy，Each time to test the final continuous punching more than three parts，And at least test every piece3～5dot，averaging。towards
2015-04-11 Reading quantity 2785
introduction：Noun interpretation： The solid lubricant powder is mixed with the powder bearing bush base material、shaping、heat，Made of sintered bearing，The case that is matched with the shaft diameter is called sintered bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]。This bearing continuously supplies a solid lubricant to the friction surface during friction。 Bearing bush matrix
2015-04-11 Reading quantity 1447
introduction：INAbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Vibration diagnosis technology includes signal acquisition、Three aspects of signal processing and fault identification。 Signal acquisition of vibration generated by rolling bearings，contain1kHzBelow the low frequency vibration and thousands of Hertz or even tens of thousands of Hertz of high frequency vibration。 Therefore, the acquisition of vibration signals is often accelerated
2015-04-10 Reading quantity 1540
introduction： Working principle The machine is composed of a feeding mechanism and a crushing mechanism。Simple structure，Easy to clean，All parts in contact with the material are made of stainless steel，acid-resisting、Alkali attack、Low noise、Work well、Low energy consumption、The broken blade can be replaced on all sides，And according to the different properties and thickness of the material by replacing the screen to obtain the ideal effect。 Scope of application The machine is widely used in pharmaceutical industry、food、Crushing of various materials in chemical industry。 Technical parameter Model number
2015-04-10 Reading quantity 2787
introduction：The sample data is stored in the sample master parts document，It could be a point，line，arc，Conic curve，Transect line， Bell curve，dimension，Drawing symbol，Surfaces and solids。Flexible use of sample drawings to repeat standard parts and add standards Message，It can greatly speed up the time to draw and produce craft cards，Save hard disk resources occupied by documents。 one、Build up sample inUGCreate the following graph：（This graphic can also be taken fromAuto CADAnd other software，passDXFTransfer to。 ）
2015-04-10 Reading quantity 2781
introduction： 1.segregation Uneven distribution of chemical composition and impurities in steel，segregation。Generally will be higher than the average composition，This is called positive segregation，Below average composition，Its called negative segregation。There is macroscopic segregation，Such as regional segregation and micro segregation，Like dendrite segregation，Segregation between crystals。 Segregation in heavy forgings is closely related to ingot segregation，The degree of segregation of the ingot depends on the steel grade、Ingot mould、Smelting quality and pouring conditions are related。Alloying element、Impurity content、Gases in steel all increase the development of segregation。The bigger the ingot，The higher the pouring temperature，The faster the pouring speed，partial
2015-04-10 Reading quantity 1514
introduction： first，We also need to inspect the bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]lube。Lubrication is very important，Not only forTIMKENbearing，Also for all bearings。But please note，The outer spherical bearing should not add too much grease。Check on bearing lubricants
2015-04-10 Reading quantity 1551
introduction：There are many kinds of lathes，According to the purpose and construction of the lathe is different，Can be divided into：General lathe、Single spindle automatic lathe、Multi-spindle semi-automatic lathe、Turret lathe、Vertical lathe、Copying and multi-tool lathes and specialized lathes、CNC lathes。Ordinary lathe、Turret lathes and vertical lathes are universal lathes。 1．General lathe This kind of lathe depends on the center height and center distance，Can also be divided into a variety of different specifications of ordinary lathes，Such asC6132、C6250Etc.。In addition, they can complete the turning of various rotary workpieces，Can also turn a variety of threads，Such as metric thread、Inch thread、Modular thread、Diametral pitch
2015-04-10 Reading quantity 1526
introduction：When designing plastic injection molds,Its design procedures and design points are roughly as follows: 1. Study and analyze product parts drawings,Master the use of plastic partsUse and appearance requirementsAssembly accuracy and determination of allowed gate and flash position.And to understand the plastic variety and its forming process. 2. Select the injection machine specificationsModel number. 3. Production batch according to plastic partsSpecifications of the injection machine and the size of the plastic parts,Determine a mold can produce several plastic parts and position layout scheme. 4. Determine the mold structure scheme.At certainty,Several mold structure forms can be conceived,Make analysis and comparison,Finally decide on an easy system
2015-04-10 Reading quantity 2885
introduction：Shaft parts turning technology For scientific management，In the production process，Often put the reasonable process of the content，Write documents to guide production。This kind of process documents that specify the manufacturing process and operating methods of products or parts are called process regulations。A part can be manufactured using several different processing methods，But under certain conditions, only one method is more reasonable。The processing process of general spindle parts is： laying-off—〉forge—〉anneal（normalizing）—〉Rough finish—〉tempering—〉semi-finishing—〉quench—〉Rough grinding—〉Low temperature aging—〉finishing。
2015-04-10 Reading quantity 2796
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
