Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Cycloidal reducer is widely used in all walks of life，The occasion of its use，Need to pay attention to relevant details and so on，All have strict requirements，Here, the use conditions of cycloidal reducer are introduced as follows： 1、Cycloidal reducer is allowed to be used in the continuous working system，Simultaneous allowable positive、Run in opposite directions； 2、The speed rating of the input shaft is1500turn/points，The input power is greater than18.5Kilowatt-hour is recommended960turn/fractional6Polar motor supporting use； 3、The working position of the horizontal installation cycloidal pinwheel reducer is horizontal。The maximum horizontal inclination Angle is general at the time of installation
2015-03-22 Reading quantity 2877
introduction：one、Machine use Sand roll rice mill is used to grind brown rice white，It is used in the process of rice mill，In the combined rice milling equipment for brown rice grinding white。 two、Overall structure Sand roller rice mill by feed hopper、Whitening chamber、Engine bed、The fan consists of four parts。 Feed hopper components are made from the feed hopper、Hopper seat、Flow regulating gate、Insert and other parts，Fixed in feed bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，with
2015-03-22 Reading quantity 2794
introduction： Which clutch is easily damaged The wearing part of the clutch is the clutch disc；Clutch failure has many aspects，If the clutch slips，Dynamic descent，Seriously cant start；Clutch disengagement is incomplete，Unable to shift，When the gear is in gear, the tooth box hits the teeth；Clutch abnormal noise，There are many reasons for this，I wont tell you all about it。 The main fault of clutch plate is driven disk warping、Deformation or friction plate is too thick、Too thin、worn、Ablative hardening、Exposed rivet、The steel sheet and the hub are broken、Hub crooked。Worn loose、Shock absorbing spring fold
2015-03-22 Reading quantity 2870
introduction： Working principle The air is converted to hot air by the heater，Access the hot air distributor located on top of the drying chamber，Then evenly into the drying chamber，And it turns in a spiral，At the same time, the feed liquid is sent to the centrifugal atomizer installed on the top of the drying chamber，The material liquid is atomized into very small atomized droplets，Liquid and hot air flow contact，Rapid evaporation of water，Dry to a finished product in a very short time，The finished product is discharged through the bottom of the drying tower and the cyclone separator，Exhaust gas is drawn out by the fan。 , sex A、Fast drying speed，The feed liquid is atomized，Increased surface area
2015-03-22 Reading quantity 2894
introduction： The structural engineer must remember the production procedure: Lets start with some engineering terms EPfingerboard(Refers to the board on which the mould parts are tested for the first time) FEPFinal test plate(Test board for the final test board meeting) PPProduction test plate(Small batch production board) PSFormal production test plate PARegular production of test plates REVImproved board AODTemporary board PMCProduction material control PURpurchase QAProduct quality assurance QCProduct quality inspection Production inspection procedures for products,To someone whos not in the business, it seems
2015-03-21 Reading quantity 2884
introduction： In the fine processing of automobile molds，Electrical machine tools should be the first choice。As the worlds top supplier of electrical processing equipment，Chamir is known for its deep understanding and careful research of EDM machine tools for half a century，It can provide high quality solutions for high value-added automotive mold processing！ A solution for excellence At present, the requirements for high-grade molds are clear texture，I.e. flat surface、Uniform roughness、Clear edges and corners、Size to fit tight seams。To meet the above requirements，It is necessary to thoroughly study the mechanism of EDM：Be sure to add
2015-03-21 Reading quantity 2783
introduction：bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]It is a fixed part in the machinery，Is the main body of machinery，Its function is basically to keep the shaft centered，And the machinery that controls that movement。IKObearing[IKObearing:IKONeedle roller bearing with its special internal structure to achieve the mechanical design of small、Light weight。Guideway bearing
2015-03-21 Reading quantity 1542
introduction： Whether your parts are suitable for automatic welding？Not all parts are suitable for automatic welding，But here is a checklist to help you decide whether to take advantage of automatic welding。 From the moment of preparation for the automatic welding process，You should ask yourself first，“Whether my parts are suitable for automatic welding？”This key question may lead you to find the answer to take advantage of automatic welding。 How does a part apply to welding including the following issues： 1） If a part was originally welded by hand，How to ensure that it is suitable for automatic welding？ 2） If its a new part
2015-03-21 Reading quantity 2790
introduction：introduction 1、 Knowledge of mold Our daily production、The tools and products we use in our lives，As big as the base of the machine、Fuselage shell，As small as a blank head screw、Buttons and casings for various household appliances，All have a close relationship with the mold。The shape of the mold determines the shape of these products，The processing quality and precision of the mold also determine the quality of these products。Because of the material of various products、appearance、Different specifications and uses，The mold is divided into casting molds、Forging die、Die-casting die、Stamping die and other non-plastic mold，And plastic molds。 In recent years，
2015-03-21 Reading quantity 2890
introduction： Analysis of clutch failure Such electromagnetic clutches as those described above，Most of the faults that occur in use are shown as open circuits。In this situation, most people will think that the electromagnetic coil should be burned out and replaced。The author found in the fault treatment of the production site that the electromagnetic coil of this kind of open-circuit fault is actually a rare case of coil burn，The most is the lead wire and slip ring from the coil(Copper ring)The welded part is loose or loose、Poor contact、The joint is burned and the coil is broken。therefore，When a fault occurs、Measured coil break
2015-03-21 Reading quantity 2791
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
