Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：The main working part of the reducer is the bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]And gear drive mechanism。The friction and wear condition of gear surface directly determines the working condition of gear。The quality of the reducer gear determines the working efficiency and life of the reducer。 Gear transmission is the most commonly used transmission mechanism in mechanical equipment，Chitro
2015-03-16 Reading quantity 2814
introduction：SKFbearing[SKFbearing:SKFThe full name is“Svenska Kullager-Fabriken”The Chinese transliterated name is“SKF”；SKFThe group is headquartered in Gothenburg, Sweden，Is a leader in bearing technology and manufacturing。SKFBearings can be divided into sliding according to different specific structures and similarities and differences in working propertiesSKFBearing and rollingSKFbearing]Use water-soluble cutting fluid，Users must work hard on machine maintenance and management，To control corrosion，And even basically eliminate corrosion。To prevent water from corroding metal surfaces，The machine should always be well oiled
2015-03-16 Reading quantity 1454
introduction：To ensure the quality of assembly，The factory bought and made some special tools，Remove and install reducer worm gear、worm、bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]、Gear and other components，Try to avoid direct tapping with other tools such as a hammer;Gear change、Worm gear when worm，Try to use original parts and replace in pairs;Assembly output shaft
2015-03-16 Reading quantity 2879
introduction： General rules for drawing forging drawings include: 1)The scale used to draw forging drawings、typeface、Graph line、Section symbol and its drawing methodGB126-74。 2)The forging outline is drawn with thick solid lines in the forging drawing；The outline of the part is drawn with double dot lines；Forgings parting lines are drawn with dot lines。 3)In order to facilitate the consideration of the size of machining allowance，The forging size number should be marked on the upper middle of the size line，The dimensions of the corresponding part of the part are indicated in square brackets in the middle and bottom of the dimension line。 4)Forgings requiring precision pressing after die forging
2015-03-16 Reading quantity 2875
introduction：By plain bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Based on the development of rolling bearings，Its working principle is to replace sliding friction with rolling friction，Usually consists of two ferrule，The versatility of a group of rolling elements and a cage is very strong、standardization、Highly serialized mechanical base parts。Because all kinds of machinery have different work
2015-03-16 Reading quantity 1534
introduction：The sludge produced by the wastewater treatment of textile printing and dyeing industry is slightly different from the sludge composition of municipal sewage，Printing and dyeing sludge generally has higher inert matter，For example, the sludge produced by denim clothing washing and bleaching wastewater has a high sand content，Organic matter、The content of pathogenic bacteria was less than that of municipal sludge，The calorific value is also low，The content of heavy metals is generally higher than that of urban sludge。And the printing and dyeing industry itself because of the use of raw materials、Product variety、The composition of sludge produced by different processing methods is also different，Enterprises that use sulphur dyes，The sulphide content is bound to be higher。Therefore, the selection and dosage of chemicals in dyeing sludge treatment should be treated differently according to the different sources of sludge，From sewage
2015-03-16 Reading quantity 2878
introduction： peculiarity： The boiling point of the material solution decreases under vacuum；The heat transfer driving force of the evaporator is increased，Therefore, the heat transfer area of the evaporator can be saved for a certain heat transfer。 The heat source of the evaporation operation can be low-pressure steam or waste heat steam Evaporator heat loss is low It can be disinfected before drying；No impurity is mixed in during the drying process；Conform toGMPdemand。It belongs to static vacuum dryer；Therefore, the shape of the dry material will not be damaged。 principle： So-called vacuum drying；The dry material is placed under vacuum conditions；Heat dry；And use vacuum
2015-03-16 Reading quantity 2781
introduction：Ceramic drying equipment selection Equipment selection of common materials Spray dryer Aluminium oxide、bentonite、Beryllium oxide、Calcium carbide、Silicon carbide、cement、electroporcelain、enamel、ferrite、Floor tile material、Glass sand、Grinding wheel material、Insulating material、Iron oxide、kaolin、sand、Silicon oxide、Spark plug material、soapstone、titanate、Tungsten carbide、Uranium oxide、Wall tile material、Zinc oxide、Zirconium silicide Tunnel dryer Ceramic product Box dryer&nbs
2015-03-16 Reading quantity 2790
introduction：What should we pay attention to when loading and unloading manual forklift trucks 1. When forkloading items，The fork spacing should be adjusted as required，Balance the load between the two forks，non-skew，One side of the item should be placed against the shelf，The weight of the fork load shall conform to the provisions of the load center curve sign。 2. The height of the load shall not obstruct the line of sight of the operator。 3. During the loading and unloading of goods，The forklift must be stopped with a brake。 4.Cargo fork when approaching or evacuating items，Speed should be slow and steady，Take care that the wheel does not run over the material，To keep the crush from stretching
2015-03-16 Reading quantity 2883
introduction： CODE：00517 Device name：Pipe bending machine Type specification：Bend diameter≥108mm Unit of measurement：Taiwan Main parameter content internation
2015-03-16 Reading quantity 2797
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
