Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：property 1、Gear is carburized and quenched by high quality alloy steel，The tooth surface hardness is high60±2hrc，High grinding accuracy of tooth surface5-6level。 2、Using computer modification technology，Preshape the gears，Greatly improve the bearing capacity of the reducer。 3、From box to internal gear，A complete modular design is adopted，Suitable for mass production and flexible selection。 4、The standard reduction model number is divided according to the torque decline form，Compared with the traditional equal proportion division，Power waste is avoided。 5、adoptcad/camDesign and manufacture，Ensure the stability of quality。 6、adopt
2015-02-02 Reading quantity 2814
introduction：The shaft is made of two bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Supported in radial and axial directions，The bearing on one side is called the fixed-end bearing，It bears both radial and axial loads，It acts as the relative axial displacement between the fixed shaft and the bearing box。The other side is called the free end，Bear radial loads only，The axis can move relative to each other。
2015-02-02 Reading quantity 1583
introduction：The drawing progressive die requires the material to be machined to have good plasticity，Must be able to adapt to multiple drawing without affecting the drawing form due to cold hardening。This is due to the belt material during the deep drawing process，Intermediate annealing is not possible，Its also not easy to use lubricants。When the progressive die is drawn，The dimensions of the workpiece should be in50mmbelow，Material thickness less than1.2mm，The thickest is not greater than2mm。 Considerations for designing deep drawing progressive dies： 1、 Because the holding force required for the first deep drawing is smaller than that of the subsequent processes，Therefore, the pressing ring of the first drawing process and the preceding cutting process must be separated from the pressing ring of the subsequent processes
2015-02-02 Reading quantity 2798
introduction： Alloy class The excess phase and the strengthened phase Antirust aluminum Al-MnSeries alloy Al-MgSeries alloy （MnFe）Al8，Al10Mn3Si（Tphase），αphase（AlFeSi），FeSiAl3，MnAl6，Mg5Al8 （β）phase，（AlFeSiMn）reachMg2Si duralumin Al-Cu-MgSeries alloy CuAl2（θphase），Al2CuMg
2015-02-02 Reading quantity 2932
introduction：rightKOYORegular maintenance of bearing equipment、It is removed during operation and replacement of peripheral partsKOYOBearings are inspected，You need to determine the next orderKOYOBearing parts can be used again and record the use of better than bad。We need to carefully investigate and document what was taken downKOYObearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，Used to reduce the friction coefficient and friction in the process of power transmission
2015-02-02 Reading quantity 1459
introduction： 1、bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The outer cover is easy to remove，Just unscrew the screw holding the bearing cap in place，You can remove the front and rear bearing covers。The front and rear bearing outer covers should be marked separately，So as not to install wrong before and after assembly。 2、The assembly method of the bearing outer cover is：Put the outer cover through the shaft sleeve at the end
2015-02-02 Reading quantity 1574
introduction： unidirectional current Unidirectional current circuit diagram Circuit diagram load characteristic Load characteristic terminal voltage Terminal voltage external characteristic External characteristic conductance conductance volt-ampere characteristics Voltammetry characteristic carb
2015-02-02 Reading quantity 2883
introduction：byTIMKENbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The steel degree determined by the structural design parameters，compliance，Quality，The vibration system composed of damping and so on will produce vibration which is suitable to its mechanics under running conditions。 Vibration caused by deviations in manufacturing processes，The smaller the deviation，The smaller the vibration。The roundness of the surface of the ball、ripple
2015-02-02 Reading quantity 1543
introduction： An important means to organize and realize the production operation plan。The main task of production scheduling in machinery industry enterprises is to understand﹑grasp﹑Prevent and deal with existing and potential problems during the execution of the production operation plan and take prompt action﹐Ensure that the project is completed on time。 Main content Assign the work according to the schedule of the work plan and the actual situation of production﹐Divide production tasks into work stations one by one﹐implementer﹐Use machining route list according to production situation﹑Single process work ticket, etc
2015-02-02 Reading quantity 2895
introduction：bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Causes and countermeasures of ring breakage Ring fracture is one of the problems that trouble bearing quality，The defect fracture is the main form of ring fracture，The main reason is the raw material itself or improper production operation，The device cannot run properly。Now combined with the actual shallow
2015-02-02 Reading quantity 1552
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
