Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The speed of the bearing is mainly limited by the temperature rise caused by friction heat inside the bearing，When the speed exceeds a certain limit，Bearings will not continue to rotate due to burns, etc。 The limit speed of the bearing refers to the limit value that does not produce friction heat that causes burns and can be continuously rotated。 therefore，shaft
2015-01-28 Reading quantity 1552
introduction：MPAandMPIThe difference of MPACan be understood as "Easy and quick" MPI。It includespart advisers and mold advisersTwo parts provide analysis of the injection molding process。The following analysis is available：Whether the product structure is reasonable 、How to choose the right injection material 、How to determine the proper gate location 、Automatic optimization of gate position 、Predict the location of the weld mark 、Whether the mold cavity is full 、How about the quality of the final product 、How to choose the right injection molding machine 、Indentation analysis 、Cost consultant。 MPISupport to
2015-01-28 Reading quantity 2908
introduction：6、Instrument configuration、Experimental equipment and laboratory requirements （note：Please contact the local sales staff for detailed configuration of the instrument） 6.1Quickly screen analytical instrument configurations(Energy dispersionXGamma ray fluorescenceEDX-720)Energy dispersion typeXGamma ray fluorescence spectrometerEDX-720type Standard softwareDXP-700E Data processing system Operation and user manual Computers and printers Molybdenum disulfide grease Vacuum silicone grease Plastic standardized samplePE-5E2 Laboratory requirements Power source：AC100V±10,15ASpecial ground wire
2015-01-28 Reading quantity 2895
introduction： Modern automobile production is characterized by a variety of models、short-period。To meet different production needs，You need to constantly change the model。Although modern computer simulation techniques are constantly being completed, various dynamics can be accomplished、However, in the research and development, it is still necessary to make real objects to verify its appearance、workwear、Installability and detachable。For shape、Parts with very complex structure can be prototyping by rapid prototyping technology to verify the design idea of the designer，The functional and assembly tests were carried out by the prototype。 Using rapid prototyping technology，Can realize the front and rear of the car
2015-01-28 Reading quantity 2874
introduction： CODE：00406 Device name：Cylindrical gear grinding machine Unit of measurement：Taiwan Main parameter content Internationally advanced
2015-01-28 Reading quantity 2846
introduction：Solid EdgeIts AmericaEDSThe middle end of the companyCAD-PDMproduct，It has powerful functional modules and a wide range of applications，Is currently one of the best 3D mechanical design software。Its excellent performance、Excellent solid and surface modeling、Professional design environment and well-known easy to learn ease of use（Basic training takes only two days），It has won wide praise from the industry。haveSolid Edge，Users can design the perfect product in the first time，Thus in the fierce market competition to take advantage of the opportunity。Solid EdgePowerful function，Easy to use
2015-01-28 Reading quantity 2925
introduction： Powered by the sudden release of energy from a high-pressure gas﹑Lower hammer head high speed movement﹐Hanging counterattack﹐Forging method for forming metal plastically。High speed hammer forging is a high energy rate forming method﹐Mainly used for precision die forging and hot extrusion。 The first high speed forging hammer appeared in1955years。figure1 Working principle of high speed hammer The working principle of the high-speed hammer。Instant release of high pressure gas(The pressure is generally15000mpa)﹐Force the hammer down9～24meter/High speed motion in seconds﹐Also push up the head of the high pressure cylinder﹐And drive the whole frame upward movement。The upper die on the hammer head and the lower die on the frame are empty
2015-01-28 Reading quantity 2828
introduction：1、Comply with casting equipment general operating procedures。 2、pre-work，Based on core height，Adjust the height of the grinding head，And lock the grinding head。 3、Check the grinding wheel for cracks，If there are cracks，Should replace the grinding wheel。 4、Start with a running test，Then run empty2-3minutes，And check the grinding wheel、Table and its transmission system（motor、 retarder）Whether the movement is smooth，Just make sure everythings okay，Before production can proceed。 5、Working hours，Start the wheel first，Then activate the rotary table；Stop in reverse order，Stop the rotary table first，Rear stop wheel。
2015-01-28 Reading quantity 2798
introduction：Compressors have a wide range of applications，Including fossilization、metallurgy、spin、Aerospace and other fields。A compressor often consists of hundreds of parts，Complex manufacturing process，High technical requirements。In order to meet the production needs of various parts，It is very important to properly equip the tool and fixture，To be satisfied in production、fast、Provincial requirement，It is necessary to improve and design some tools and tooling。Here are three examples： Milling clutch flange tools and tooling improvements The shape of the spiral tooth clutch with one-way action is a spiral end tooth structure，As shown in the figure1，Its role is when
2015-01-28 Reading quantity 2794
introduction：timkenCylindrical roller bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The reasons for the emergence of cold temperatures include：Not enough or too much smoothing；The glossy contains publications；overload；Bearing protection；Gap excess and low temperature conflict of oil seal。 When the bearing is already in a different condition，It usually manifests itself at low temperatures。
2015-01-28 Reading quantity 1455
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
