Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： The clutch is located in the flywheel housing between the engine and the gearbox，Fasten the clutch assembly to the rear plane of the flywheel with screws，The output shaft of the clutch is the input shaft of the gearbox。While the car is moving，The driver can depress or release the clutch pedal as needed，Temporarily detach and gradually engage the engine and gearbox，To cut off or transmit power from the engine to the transmission。 The clutch is a common part in mechanical transmission，The drive system can be separated or engaged at any time。The basic requirements for it are：Jointing smooth，The separation was swift and complete;Easy to adjust and repair;Small profile size;
2015-01-07 Reading quantity 2813
introduction： The heat generated by the friction between the end faces of the workpiece is used to make it reach a plastic state，Then the top forging completes the welding method。When turning the workpiece, the chips tend to stick firmly to the tool head，Poor lubrication between the shaft and the bushing can also result in partial welding，Friction welding was invented from these phenomena。Friction welding can be divided into two types: continuous drive friction welding and inertia friction welding。①Continuous drive friction welding:A workpiece is rotated by an electric motor,At the same time, another workpiece is pressed towards the rotating workpiece，Make the contact surface friction with each other to produce heat and a certain plastic deformation,And then stop spinning,At the same time, the forging pressure is applied to complete the welding(figure1[Continuous drive
2015-01-07 Reading quantity 2796
introduction：one、About internal clearance A、Gap basic definition：Industrial terminology，Used for bearings in general purpose accessories[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Broad category。Its the inner ring of the bearing、Outer ring、The amount of clearance between the rolling elements；It is an important technical quality requirement project in the national standards，Its also an important check item，It is also important in bearing applications
2015-01-07 Reading quantity 1466
introduction： Content summary： This paper expounds the organization mode of computer technology and CNC machining technology in modern mold manufacturing after the introduction of virtual technology concept 0．introduction At present, Virtual manufacturing technology has not yet formed a complete theoretical system, It is generally believed that it is supported by high-performance computers and high-speed networks, Supplemented by various special equipment and instruments, Not in fact but in essence, The process of turning raw materials into products is realized on the computer。The subject has shown full flexibility from the day it was proposed、、Economic advantage, It attracts researchers from many different disciplines。This text
2015-01-07 Reading quantity 2807
introduction： one、Product introduction KJ205Coal mine cable industrial TV monitoring system is mainly used in coal mine safety production important links、site、And the departments TV surveillance，The images of each monitoring point can be collected and transmitted to the central monitoring room and displayed on the monitor in real time。Through this system，Surface monitoring personnel can intuitively monitor and record the safety production situation of the underground work site，Timely find the illegal operation of each monitoring point，Take precautions against trouble，For the safety of coal mine production escort。 two、Technical characteristics 1.The system adopts the common cable transmission mode，Multiple monitoring point signals share a single cable transmission，Large knot
2015-01-07 Reading quantity 2811
introduction：Geometric accuracy of pairs、Precision guide rails with high motion accuracy and positioning accuracy requirements（Such as CNC machine tools and measuring machine guide rails），The following principles should be followed when designing： 1.Error compensation principle Meet the following three requirements，In order to make the guideway system error mutual compensation： （1）Intermediate elastic links must be arranged between guide rails，Such as rolling body plastic belt（slice）Or fluid film, etc。 （2）There should be sufficient preload force between guide rails，To compensate for contact errors。 （3）The manufacturing error of the guide rail should be less than that of the intermediate elastomer（mods）Deformation of。 2.Mutual accuracy
2015-01-07 Reading quantity 1708
introduction：（1）Long service life，It can reduce the maintenance cost，decreaseTIMKENbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Frictional consumption。 （2）The right consistency，It has good vibration reduction function，Reduced speedTIMKENBearing noise，Conducive to environmental protection。 （3）Good antioxidant properties，Use
2015-01-07 Reading quantity 1550
introduction：How to use manual forklift 1、Single side use plastic tray Flat nine-legged plastic tray、Mesh nine-legged plastic tray（Flat nine-legged plastic tray 、Mesh nine-legged plastic tray （ Mechanical or manual All can be used in four directions） All can be used in four directions ）Flat plastic tray、Grid type plastic tray（ Flat plastic tray 、Grid type plastic tray （For mechanical use only The forklift is used in four directions）The forklift is used in four directions ） Flat, flow-line plastic tray、Grid stream type plastic tray（ Flat, flow-line plastic tray 、
2015-01-07 Reading quantity 2842
introduction：Needle roller bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]There are three things about burns：Bearings are poorly lubricated；Imported bearing[Imported bearing:Simply put, the import bearing agent refers to the sale of an imported bearing brand。The main brands of imported bearings arenskbearing，ikobearing，fagbearing，Of good quality，Natural price
2015-01-07 Reading quantity 1541
introduction：KOYOBearing in addition to excellent quality，Its a very sophisticated part，Both high-performanceKOYObearing，If used improperly in the course of use，Not only can not achieve the expected performance effect，And its easy to makeKOYOBearing failure，Everyone must have been paying attention to lubrication。Besides lubrication，KOYObearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，Used to reduce the coefficient of friction and protection in the process of power transmission
2015-01-07 Reading quantity 1468
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
