Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Lifting and transportation machinery bearing applications，For the special application environment in this field，Huagong bearing Special sealing designs are also available、Anti-corrosion and anti-rust products。
2017-05-28 Reading quantity 196
introduction：The steps to install and lock the guide rail slide are as follows：1、Gently place the table on the linear guide slide block,Incomplete locking of mounting bolt。2、The reference side of the linear guide slide block is contacted with the datum surface on the side of the table by the stop screw，Set the table。 3、Fully lock the base and driven side assembly bolts,Complete installation。
2017-05-27 Reading quantity 438
introduction：Linear guide bearing is the common name of some people，Generally refers to the linear optical axis（Includes a variety of flanged linear bearing blocks）、Linear guiding optical axis、Linear circular guide（Includes linear guide housing assembly sliding unit and flange type guide shaft support）。
2017-05-27 Reading quantity 292
introduction：The correct installation of the robot reducer is very important and directly related to the later use，Improper installation can damage the reducer，Later use will also be affected，How to use and maintain the reducer，It is an important link to ensure the normal operation of mechanical equipment。therefore，When installing a robot reducer，Please strictly follow the installation and use instructions below，Assemble and use carefully。
2017-05-27 Reading quantity 297
introduction：Deceleration motor wholesale where is good？Now the market reducer manufacturers and brands are very much，The information on the Internet is also very rich，Search at random，A lot of gear motor manufacturers came out，But how to know which reducer is better？Today Xiaobian will introduce you to some good ways to choose a reducer manufacturer。
2017-05-27 Reading quantity 212
introduction：Mild steel（mild steel）Is less than carbon content0.25%Carbon steel，Because of its low strength、Low hardness and soft，It is also called soft steel。It includes most of the ordinary carbon structural steel and a part of high-quality carbon structural steel，Most of them are used for engineering structural parts without heat treatment，Some are carburized and other heat treatment for mechanical parts requiring wear resistance。 The annealed structure of low carbon steel is ferrite and a small amount of pearlite，Its strength and hardness are low，Good plasticity and toughness。therefore，Its cold formability is good，Curling can be used、bend、Cold forming by stamping and other methods。This steel also has good weldability。Carbon content from0.10%to0.30%Low carbon steel is easy to accept various processes such as forging，Welding and cutting， Often used in the manufacture of chains， rivet， bolt， Axis scheduling。
2017-05-27 Reading quantity 237
introduction：The limit speed of angular contact ball bearing is higher，It can withstand both radial and axial loads，It can also withstand pure axial loads，The axial load capacity is determined by the contact Angle，And it increases with the increase of the contact Angle。Single row angular contact ball bearings can only withstand axial loads in one direction，Under radial load，Will cause additional axial force，The corresponding reverse load must be applied，therefore，The bearings are generally used in pairs。Double row angular contact ball bearings can withstand large radial loads、Axial bidirectional joint load and torque load，It can limit bidirectional axial displacement of the shaft or housing，The contact Angle is30The degree of。Angular contact ball bearings mounted in pairs can withstand radial loads mainly、Axial bidirectional combined load，It can also withstand pure radial loads。The series configuration can only withstand axial loads in a single direction，The other two configurations can withstand axial loads in either dir
2017-05-27 Reading quantity 200
introduction：INAIf the bearing is in a superior continuous rotation pattern, it will announce a low whine sound and a noise will occur when the knock wound，This noise will vary with the bump of the thin-wall bearing speed。If there is intermittent noise，resethrough。If you announce a sharp hissing sound，Squeaking and other irregular sounds，It is often revealed that the performance bearing is in poor continuous rotation。For heavy loads, grease with small needle penetration should be selected when working under high pressure except for small needle penetration，It also has high oil film strength and extreme pressure performance。When choosing grease according to environmental conditions，Calcium-based greases do not dissolve easily in water，Suitable for dry and less moisture environment。INABearings commonly used grease are calcium base grease sodium base grease calcium and sodium base grease lithium base grease aluminum base grease and molybdenum disulfide grease。The amount of grease filled in the bearing，To fill the bearing int
2017-05-27 Reading quantity 268
introduction：Present Day，Flanged linear bearings are very common in life，However, the disassembly of flange linear bearings is not very well understood，During the entire disassembly process，In case of a problem，Easy to damage the quality of the bearing，Affect the full performance of the product itself。
2017-05-27 Reading quantity 311
introduction：With the needs of market development，Linear bearings play an increasingly important role in the market，The use of machinery in various industries is very large，Has an increasingly important role in the market，
2017-05-27 Reading quantity 284
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
