Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Servo motor bearing overheating
1.Fault cause
① Too much or too little grease；
② The oil is bad and contains impurities；
③ Improper fit of bearing with journal or end cap（Too loose or too tight）；
2016-01-22
Reading quantity 1520
introduction：Abstract:Understanding the temperature range of various pressure sensors is very helpful for us to choose pressure sensors，When choosing a pressure sensor, we can choose the sensor we need well, which does not waste resources and can meet our requirements。 Pressure sensors both in industry、Both agriculture and services have wide applications。but...
2016-01-22 Reading quantity 2119
introduction： Servo motor in the case of its own drive，Belongs to a separate system，At this time, the connection of the inverter can not achieve the effect of direct drive。Communication interface in servo controller and inverter，When synchronization or other communication functions can be achieved，Can realize the connection，But also need to have a premise is the frequency converter and
2016-01-22
Reading quantity 1657
introduction： 1 introduction Programmable controller（PLC）It is a new type of general automation control device，It will be traditional relay control technology、Computer technology and communication technology are integrated，It has strong control function，High reliability，Flexible and convenient，Easy to expand and other advantages and more widely used。But in use due to industrial production site...
2016-01-22 Reading quantity 1633
introduction：
gx developer:Mitsubishi full rangeplcProgramming software,Support ladder、Instruction list、sfc、standfb、labelLanguage programming，Network parameter setting，Online changes to the program can be made、Monitoring and debugging，Writing structured programs(Sectional programming)，Can be made into a standardized program,Used in other similar systems。
2016-01-22
Reading quantity 1688
introduction：The executive parts and mechanical transmission parts on the machine tool constitute the feed system of the CNC machine tool，It controls the feed speed of the actuator according to the speed and displacement instructions sent by the numerical control device、Direction and displacement。Each actuator of the feed motion is equipped with a servo system。The function of the servo system is to convert the pulse signal from the numerical control device into the movement of the moving parts of the machine tool，It corresponds to the hand of a manual operator，bench（Or slide）Precise positioning or strict relative movement according to the specified trajectory，The most...
2016-01-21 Reading quantity 1947
introduction：Coupling is used to connect the prime mover shaft and slave mover shaft of electromechanical equipment，The driver device runs properly，It also has the ability to compensate the two-axis deviation；From the coupling characteristics known：Air bag clutch，Hydraulic coupling，Centrifugal couplings have overload protection，But the centrifugal coupling and air bag clutch do not have the ability and conditions to absorb the impact load(It turned out that the centrifugal coupling had caused damage to the equipment)，So choose the hydraulic coupling asFP5012Crusher new coupling device in addition to the coupling also has...
2016-01-21 Reading quantity 1871
introduction： ◆To avoid misoperation of the drive，Make sure to cut off the main power supply of the device and confirm the safety before installing。 &nb...
2016-01-21 Reading quantity 1842
introduction：Wire-cut machine tools are not suitable for working in dirty and hot and humid environments，Grid power supply environment also has higher requirements，The machine power supply voltage should not be inferior to±10%，Three corresponding equilibrium stability。Wire cutting machine too bad power grid must be installed voltage regulator。Wire-cut machine tools are kept clean and lubricated in addition to normal，The following parts must also be carefully maintained： &nbs...
2016-01-21 Reading quantity 1936
introduction： 1 lead said Due to high precision、High speed、Rate and safe and reliable characteristics，In the updating of manufacturing technology equipment，CNC machine tools are rapidly gaining popularity in enterprises。Numerical control machine tool is an automatic machine tool equipped with program control system，Able to follow the programmed program，Make the machine move and process parts。It combines machinery、automate、compute...
2016-01-21 Reading quantity 1825
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
