Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：The reducer refers to an independent closed transmission device between the prime mover and the working machine，Used to reduce the speed and increase the torque accordingly。In addition，On some occasions，There are also devices used as speed increases，And called speeder。 There are many kinds of retarders，This article only discusses by Gear drive、Worm drive and the reducer composed of them。If it is divided according to transmission and structural characteristics，This kind of reducer
2015-12-23 Reading quantity 1953
introduction：1)The cumulative transmission clearance of the reducer。Because the mold shaking table is connected with the eccentric shaft through the connecting rod，The weight of the mould and shaker is very human(Gross re-reduction16t),When the mold is near the upper and lower door points，The torque direction of the eccentric shaft is abrupt，The meshing teeth of the reducer change from one side of the teeth to the other。The transmission of the reducer accumulates clearance time，It will cause the mold to vibrate
2015-12-23 Reading quantity 1900
introduction：Several matters should be paid attention to when choosing the type of reducer：Try to use close to the ideal deceleration ratio：Reduction ratio=Servomotor speed/Calculation of torque of output shaft of reducer：For the life of the reducer，Torque calculation is very important，And pay attention to the maximum torque value of acceleration（TP），Whether it exceeds the maximum load torque of the reducer。 The applicable power is usually the servo on the market
2015-12-23 Reading quantity 2023
introduction：Chinas rolling function parts industry production is not concentrated、Single product variety、Low gold content、There is not yet a well-known brand with international influence，It has become the bottleneck of the development of domestic CNC machine tools。therefore，It is necessary to accelerate the industrialization of rolling function parts in our country。 Rolling feature products include：Ball screw pair、Rolling linear guide pair、Ball spline、Ball guide bush
2015-12-24 Reading quantity 2205
introduction：The reducer is an independent closed transmission device between the prime mover and the working machine，Used to reduce speed and increase torque，To meet the needs of the job，In some cases also used to speed up，speeder。 There are many kinds of retarders，According to the transmission type can be divided into gear reducer、Worm reducer and planetary reducer and their combined reducer；According to the transmission of the series can
2015-12-23 Reading quantity 2056
introduction：Currently in the CNC cutting machine products，Many product parts，All require careful maintenance and selection，Especially the new CNC cutting machine products，It is necessary to understand the products and performance of CNC cutting machine，Otherwise, if something goes wrong，Its hard to deal with.。 The commonly used servo motor is AC servo motor，The shaft end of the motor is equipped with a photoelectric encoder，Pass check turn
2015-12-23 Reading quantity 2087
introduction：keyword： Servo driver Abstract：This paper introduces several common faults of servo drivers and their countermeasures。 Common fault analysis of servo drive： 1、The motor deviation counter overflow error occurred when the servo motor was rotating at high speed，How to deal with? ① Motor deviation counter overflow error occurred during high speed rotation; counterplan： Check the wiring of the motor power cable and encoder cable
2015-12-23 Reading quantity 2108
introduction：Industrial control abstract： The requirements of CNC machine tools for feed servo motors are mainly: （1）Mechanical characteristic:The speed reduction of the servo motor is required
2015-12-23 Reading quantity 2038
introduction：When the CNC machining center system issued instructions，The servo unit or servo motor does not execute，Or because the servo deviation value detected by the system is too large，So wait for this deviation value to change
2015-12-23 Reading quantity 2032
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
