Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：[coupling100A question and answer（Under the）]:61．What is a safety coupling？a：Couplings with overload safety protection。 62．Safety couplings are divided into several categories？ a：Divided into pin type：LFN type flexible loose pin coupling；Friction type：MAL Friction safety coupling andAMNInternal tension friction coupling，Magnetic particle type、centrifugal... 61．What is a safety coupling？
2015-12-28 Reading quantity 2128
introduction：①The tooth surface is badly worn。 ②The axial displacement of the inner gear ring is large，Cant even mesh。 ③A broken tooth occurs。 ④Coupling bolt is broken。 The causes of the above faults are mainly as follows： first，Lack of oil or oil in the coupling of lifting accessories。Or improper use of grease，Causes the oil to calcify，Resulting in no lubrication between tooth surfaces，Or poor lubrication to produce tooth surface
2015-12-28 Reading quantity 2321
introduction：anything，All have their own terminology in the industry，Computer has a technical term for computer，Then the coupling works on the components of a machine，Of course, there are also common technical terms，Here is to explain the terms of the coupling。 ◆Rated torque：Refers to the continuous transmission of torque capacity of the coupling。Variable load factors during operation are taken into account，So there is no need to adjust the rated torque。please
2015-12-28 Reading quantity 1989
introduction：The clutch is an important part of the automatic press，It works with the press brake，Under long hours of work，The clutch will have a series of failure problems，Especially when the staff press the button after the clutch does not work，Sometimes there are violent shocks，Whats going on here？How should we deal with the impact failure of the automatic press clutch？Automatic punch
2015-12-28 Reading quantity 2253
introduction：On the structure and operation of diaphragm coupling： one Diaphragm coupling structure form ：4hole 6hole 8hole 10hole 12hole 1、The form of the diaphragm： Continuous multilateral ring、toroidal、Disconnecting linkage、spoke、Formed diaphragm，Corrugated diaphragm。 2、Continuous multilateral ring、Circular features： Each coupling consists of a number of diaphragms of equal thickness，The outer edge of each piece is an arc
2015-12-28 Reading quantity 2005
introduction：Linear guide information：China is the worlds largest consumer of machine tools，Manufacturing has developed into a pillar industry。Due to the development of the automobile industry，The speed and efficiency of machine tools are put forward new and higher requirements。It is understood，At present, the CNC rate of machine tools in China is developing rapidly。Japanese machine tool CNC rate from the beginning40%Bring up to date90%The level of，About spend1
2015-12-28 Reading quantity 2233
introduction：Worm gear reducer is a compact structure、Large transmission ratio，Transmission machinery with self-locking function under certain conditions。And easy to install、Reasonable structure，It has been used more and more widely。It is to install a helical gear reducer at the input end of worm gear reducer，The multistage reducer can obtain very low output speed，It has higher efficiency than single stage worm gear reducer
2015-12-28 Reading quantity 1999
introduction：The input shaft of the reducer is connected to the motor by a pin coupling with a brake wheel。This kind of coupling is allowed to have a certain installation deviation，however，The impact caused by the runout and swing of the reducer has a great impact on the service life of the pin，Causes frequent cutting of pins。The coupling is equipped with a brake wheel，Motor alignment、Installing pins takes time and effort。Sometimes due to the third class homework，
2015-12-28 Reading quantity 1998
introduction：Abstract:In order to better help the majority of users with a good planetary reducer，In this paper, the causes of shaft breakage of reducer and drive motor are analyzed In order to better help the majority of users with a good planetary reducer，In this paper, the causes of shaft breakage of reducer and drive motor are analyzed，The problem of broken shaft of planetary reducer is introduced in detail。 Some users drive down the device after several months of operation
2015-12-28 Reading quantity 2015
introduction：Public interestQS7Application of servo drive system in CNC lathe，The feed shaft requires high speed operation1200rpm，It starts and stops smoothly。When running at constant speed, the load changes little。High speed and accurate positioning is required when the cutting shaft is set to the tool，The actual cutting speed is very low0.1-10rpm,It is required to run smoothly at low speed and not be affected by heavy loads。
2015-12-28 Reading quantity 711
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
