Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Aeroengine bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Advanced material 1.M50NiLBearing steel from1955Turn of the year1980years25During a certain age，The speed of aero-engine bearing increases steadily，dnThe value has reached close2.5million。Into the nineties，The high speed and high temperature of an aeroengine roll
2014-12-30 Reading quantity 1456
introduction：one、bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Industry status and heat treatment technology and equipment overview 1.Chinas bearing industry sustained rapid and stable development Chinas bearing industry after more than 50 years of construction and development，Especially since the reform and opening up、fast、Steady development，Has formed a larger
2014-12-30 Reading quantity 1433
introduction： The performance of automobile clutch disc failure 1、The diaphragm spring of the diffuser is too soft or broken，The conflict surface of the clutch pressure plate or flywheel is worn out with grooves(Rivet head scraping)、Warp or grind out steps。 2、The hub of the follower disk is stuck on the shaft of the follower or stagnates。 3、Transmission shaft front bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts are on the shaft
2014-12-30 Reading quantity 2783
introduction： Welding technique Optimum assembly technique---Part two In addition to this series No7Section described in the assembly techniques outside，There are many other different welding methods that can be used in the connection of plastic parts。To ensure low costs、Effective functional design，In the early stages of design，It is very necessary to choose a suitable welding method，Full consideration is given to the required connection geometry。 The assembly of plastic parts that are permanently joined without other assembly parts can be done by welding。The selection of welding methods is based on the following criteria：According to the geometry of the molded part，used
2014-12-30 Reading quantity 2803
introduction： Needle roller bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Its a mass production of mechanical parts，And the manufacturing accuracy requirements are very strict，There is a high degree of technical specialization，Therefore, for the vast majority of easy to buy bearing varieties，It should be more cost-effective to buy than to repair，Apart from economics，The repair of bearings is also technical，It is necessary that...
2014-12-30 Reading quantity 1452
introduction：(1)New water pump put into service，Generally in operation100Replace the grease after hours(oil)，Subsequent run500Hourly replacement1time。 (2)Flow bearings lubricated with grease[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]，operation1500Hours later，Grease should be replaced，The amount of oil should not be too much or too little
2014-12-30 Reading quantity 1438
introduction： Domestic and foreign bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]New technology of steel rolling （1） Austenite single-phase zone rolling technology； Finishing rolling is controlled in austenitic single-phase zone。As the most basic rolling process，The properties of the rolled products are normal，All need to do post-heat treatment。 （2） austenite
2014-12-30 Reading quantity 1463
introduction：The reducer is generally injected with grease，Molybdenum disulfide is used-2orZL-2Lithium lubricating oil, etc。 Cycloidal pin gear reducer manufacturers in order to facilitate loading and unloading and transportation，Usually no lubricating oil is injected，Oil is only injected before use，Recommended at room temperatureN150Extreme pressure industrial gear oil。 Lubricating oil change cycle： The reducer is in its first run200The first lubricating oil change must be made after hours，The remaining dirty oil should be removed during replacement。After the initial oil change，Work continuously every day10More than hours of reducer，Should be every other3Change the lubricating oil once every month、Work no more than one day10a
2014-12-30 Reading quantity 3278
introduction：This article isEdgeCAMA case in text engraving，In this paper, the author describes in detail the vector text andTrueTypeText inEdgeCAMThe generation process in software，The relevant processing precautions are also given。 In the manufacture of molds, etc，The use of words is relatively common，You can use dedicated software to make convex or concave carvings where you need them。In addition to using some professional carving software，Make use ofEdgeCAMYou can also do this kind of work easily。 one、Text placement EdgeC
2014-12-30 Reading quantity 2804
introduction：one、Feature： China is the worlds largest fruit production country，Chinas total apple production accounts for the worlds total output24%，The per capita share of the country reached53kilogram。Fruit has become a rural economy Pillar industry。Due to the large yield of fruit，Fresh-keeping processing ability is not root，So there is a big problem of selling fruit。It has affected the enthusiasm of fruit farmers！ Apples sales outlet lies mainly in the deep processing of apple。This complete set of equipment is dry production of apple powder。 Apple powder is mainly used in：food、additive、beverage、Cold food、filling、Food for the aged
2014-12-30 Reading quantity 2772
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
400-8040668
Official wechat public account
Order for goods/Information at hand
