Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：Pressure rivet nut is also called rivet nut，Self-tightening nut，Is a nut applied to sheet or sheet metal，Round shape，One end is provided with embossing teeth and a guide groove。The principle is to press into the preset hole position of the sheet metal through the embossing teeth，In general, the aperture of the preset hole is slightly smaller than the embossing teeth of the riveted nut，The teeth of the riveted nut are pressed into the plate by pressure causing plastic deformation around the hole，The deformation is squeezed into the guide groove，Resulting in a locking effect。
2017-03-28 Reading quantity 202
introduction：cpcGuide rail model list CPCGuide type list： microguideMR-MLseries microguideMR-MNseries Wide guideMR-WNseries Wide guideMR-WLseries MR3ML MR3MN MR3WN M...
2017-02-25 Reading quantity 206
introduction：Single row angular contact ball bearings can only withstand the axial load in one direction，Under radial load，Will cause additional axial force。 And only limit the axial displacement of the shaft or housing in one direction。The contact Angle of the angular contact ball bearing is40The degree of，Therefore, it can withstand a large axial load。Angular contact ball bearings are of non-separation design，The shoulders on both sides of the inner and outer rings are not high or low。In order to improve the bearing load capacity，Its gonna lower the shoulder on one side，This allows the bearing to fit more steel balls。 Double row angular contact ball bearings can bear large radial loads mainly radial and axial combined loads and torque loads，Limit the axial displacement of both sides of the shaft。It is mainly used in parts that limit the bidirectional axial displacement of shafts and housings Double row angular contact ball bearing inside、The inclinability between the outer rings is limited，The allowable inclinati
2017-06-16 Reading quantity 227
introduction：Angular contact ball bearing load capacity The following is for the load capacity of the paired bearing only ，The basic rated load and fatigue limit load given in the product table are only applicable to a single bearing。 *Basic rated dynamic load，Standard bearings for any configuration and back-to-back or face to face configurationsSKFExplorer bearing C=1，62xCSingle bearing *Basic rated dynamic load，For series configurationSKFExplorer bearing C=2xCSingle bearing *Basic static load rating Co=2xCoSingle bearing *Fatigue limit load Pu=2xPuSingle bearing
2017-06-19 Reading quantity 305
introduction：The working principle of time delay relay is described briefly
2016-03-07 Reading quantity 294
introduction：At present, the coupling method of coupling sleeve and taper pin is mainly used for rigid coupling，And most feed motor shafts are equipped with flat keys。This connection，After a period of use，The conical pin began to loosen，The side clearance of the keyway gradually increases，Sometimes it even causes the taper pin to fall off，Cause parts processing dimension is unstable。
2017-03-08 Reading quantity 202
introduction：TaiwanCPCLinear guide agent? TaiwanCPCFeatures of linear guide Low wear can maintain accuracy for a long time Traditional slide guidance，It is inevitable that the platform movement accuracy will be poor due to the countercurrent action of oil film，And due to insufficient lubrication during exercise，It causes the wear of the contact surface of the running track，Seriously affect accuracy。The wear of the rolling guide is very small，Therefore, the machine can maintain accuracy for a long time。
2017-03-23 Reading quantity 157
introduction：CPCLinear guide? CPClinear?introduction CPCLinear guide is a kind of rolling guide，An infinite rolling cycle between the slider and the rail is performed by the steel ball，The load platform can easily move linearly along the slide rail with high precision。In addition, the beam unit design between the slide block and the slide rail is added，makeCPCLinear guide can bear the load in all directions at the same time，The above display features are not comparable to traditional slide guidance，Therefore, if the machine can match the ball screw，UseCPCLinear guide rail for guidance，It can greatly improve equipment accuracy and mechanical efficiency。Compared with traditional sliding guidance，The friction coefficient of the rolling guide can be reduced to the original1/50，Due to the starting friction is greatly reduced，Relatively little ineffective movement occurs，So it can be easily achievedμmProgressive feed and positioning。
2017-03-29 Reading quantity 271
introduction：With the growth of use time，The slider may lose its recoil-free function due to wear and tear，But the center slider is not expensive，Its also easy to replace，It can still play its original performance after replacement。Slider couplings are commonly used in general motors，Individual occasions can also be used to connect the servo motor，The relative displacement is corrected by sliding the center slider during use。
2017-03-11 Reading quantity 205
introduction：With the acceleration of automation，The application range of synchronous belt slide is also expanding，Straight slide table development so far，Has been widely used in a variety of devices。So how does the synchronous slide work？
2017-03-02 Reading quantity 354
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
400-8040668
Official wechat public account
Order for goods/Information at hand
