Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：1、Upper base foot screw initial adjustment bed level。 2、Remove all fixing plates and support seats 3、willXAxial sumYScrew the screw nut on the shaft evenly screwed straight Angle iron（Screw down） 4、Install all machine sheet metal or shields 5、Clean countertop、Anti-rust oil for fixture and wire bucket。 6、Lead screw、Lubricate moving parts such as guide rails。 7、Fine adjustment of machine level requirements1000mm
2015-12-28 Reading quantity 1866
introduction：introduction：How to check the reducer？How to maintain the reducer？ retarder 1.First of all, check the gear transmission oil of the reducer，The type of lubricating grease is selected according to the bearing load of the travelling reducer，For the heavy-duty reducer, the grease with small needle penetration should be selected，Minor needle penetration exception when working under high pressure，There are higher
2015-12-28 Reading quantity 2078
introduction：cause 1、The slide is inclined and sunk due to the wear of machine guide rail，Bend the lead screw and engage the opening nut poorly，In a single mesh。 2、Carrier support hole wear，Make the lead screw rotating center line unstable。 3、The axial clearance of the lead screw is too large。 4、The hanging axle of the tool box is bent。 5、There is a gap between the drag plate and the slide plate in the square tool holder。 6、Square tool holder and small tool holder base plate connection
2015-12-28 Reading quantity 2175
introduction：Tension machine mainly by the main engine、computer、jig、Sensors and other components，The screw is also one of the accessories of the tension machine。At present，There are mainly two kinds of ball screw and trapezoid screw common on the market。The customer is selecting the tension machine，Sometimes I ask what is the difference between these two screws？Which is better？For the customers question force high Xiaobian in this summary of a few points，To the customer
2015-12-28 Reading quantity 2094
introduction：Clutch installation precautions ●The clutch must be cleaned before installation，Remove anti-rust grease and debris。 ●The clutch can be mounted coaxial，It can also be mounted on separate shafts，The axis must be fixed，The active part and the driven part are not allowed to have axial movement，When the shaft is mounted，The coaxiality between the active part and the driven part axis should not be greater than0.lmm。 ●When wet electromagnetic clutch is working
2015-12-30 Reading quantity 2015
introduction：Introduction to couplings coupling Today I will explain the content of the coupling for you，With the development of technology，Couplings will be more and more widely used in society。The prospect of this coupling is very good，This paper collects some information，I hope this article can be of great reference value to readers。 Couplings are used to join two axes in different mechanisms（initiative
2015-12-30 Reading quantity 2003
introduction：Flat washers are used where bolts need to be removed frequently，To protect the surface of the connected part from being scratched，Generally, it is necessary to place a flat washer at the nut or bolt head，This can prevent the surface of the connected part from being scratched，Especially for precision machined surfaces。In some joints where the coefficient of friction requires more precise，There is no separate test requirement for the coefficient of friction，Like wind power bolting，General purchase bolt、nut、Gasket coupling pair。In this case bolt、nut、Gaskets are all supplied by the same manufacturer，Bolt manufacturers need to treat nuts and washers accordingly，To secure the nut with the pad
2021-11-08 Reading quantity 771
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
400-8040668
Official wechat public account
Order for goods/Information at hand
