Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Fatigue failure is a surface form of failure，The main manifestation is the initiation of fatigue cracks，Expansion and fracture processes，The long-term effects of failure of the metal under alternating loads。The sealed plain bearings are lubricated with specially tested, high-quality lithium based greases。This grease
2015-05-06 Reading quantity 1667
introduction： ug Default metric ugii_env.datInside set。 UGII_DEFAULTS_FILE=${UGII_BASE_DIR}ugiiug_metric.def ugChange unit 1. Its just that the units change and the actual length stays the same. a. Unigraphics NX->UG Command Prompt b. Cd UGII c. Ug_convert_part -in
2015-05-06 Reading quantity 2861
introduction：The drawing die is to draw and press the blank into a hollow body，Or the hollow body is pulled and pressed into a smaller shape of the hollow body without significant changes in plate thickness of the die。 Drawing die structure form 1.Die for the first deep drawing process（table1） 2.Die for subsequent deep drawing process（table2） 3.The reverse drawing die deepens the process parts in the opposite direction of the previous process，Its called reverse drawing。Reverse drawing turns out the inner wall of the process parts，Large contact surface between process parts and die，Material flow resistance is also large，Therefore, the press ring is not required。figure1Is an example of reverse drawing。figure2in
2015-05-06 Reading quantity 2973
introduction：It is the season of flood control and drought relief，Agricultural pumps are widely used，How to properly use and maintain agricultural pumps for irrigation、Drainage and the proper operation and life of the pump are critical。 one、Installation of water pump The installation and calibration of the pump is a critical first step，Although the pump unit has been corrected at the factory，But due to transportation、Assembly and other reasons，Can lead to varying degrees of deformation or loosening，therefore，The water pump should be installed side by side during installation、Edge correction。 1、Mounting polymerization (1)Remove grease and dirt from the base，Place the base on the foundation。 (2)Use a level
2015-05-06 Reading quantity 2985
introduction： one、Improper installation(Account for about16％) 1、Use brute force when installing，Hit the bearing directly with a hammer[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The greatest damage to bearings；It is the main cause of deformation。 2、Inadequate installation，Mounting is deviated or not installed to the bearing position，Cause the bearing clearance is too small。Inside and outside
2015-05-06 Reading quantity 1520
introduction： INAbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Usually the space that can be installed is limited。In most cases，shaft（orINABearing diameter）Is based on mechanical design or other design limitations。Bearing type and size，Therefore, bearings in the New Territories North region are selected
2015-05-06 Reading quantity 1503
introduction： Using liquid as the working medium﹐A fluid drive that relies on the hydrodynamic action between the impeller and the liquid to transfer energy。The impeller will power the machine(Internal combustion engine﹑motor﹑turbine)Input speed﹑Torque conversion﹐The working part of the machine is driven by the output shaft。The liquid is loaded with the input shaft﹑Output shaft﹑The impellers on the shell interact﹐Produces a change in the moment of momentum﹐Thus achieving the purpose of transferring energy。Hydraulic transmission and hydraulic transmission by liquid pressure energy to transfer energy in the original
2015-05-06 Reading quantity 2867
introduction：Chemical composition Rolling bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]steel：GCr15，GB/T18254—2000《High carbon chromium bearing steel》 Unified digital code grade chemical composition，％ B00150GCr15&nbs
2015-05-06 Reading quantity 1507
introduction：steel Carbon content is less than2％An iron-carbon alloy containing certain other elements。Steel has high strength、Good toughness、Easy to form、Abundant raw material resources、Easy smelting、Cheap price and other advantages，It is the most widely used metal material。 Brief history China is in the late Spring and Autumn period（before476Years ago)There has been artificial exercise of steel。By the Eastern Han Dynasty had mastered the technology of frying steel。The crucible method was first used in the industrial production of steel，Low yield、High cost，It is difficult to meet the needs of industrial development。1856years，AnglicanH.Bessemer invented the converter steelmaking process，1856～1864years，AnglicanK.W.the west gate
2015-05-06 Reading quantity 2993
introduction：Reducer imports domestic entrance：Nord，Friend，SEW，Rexroth，Bonfiglioli， 1、GermanySEWcorporation SEWReduction gear，Products cover a wide range，Simple structure，Variable mounting style，Flexible use，modularization，The motor reducer can be separated or combined，Is most of the domestic reducer to emulate the object，The earliest conversion manufacturers in China，Ningbo Dongli，Zhejiang Kone，Omet，Guo MAO is a rising star。 2、Nord GMBH Reducer high-end brand，Reducer inverter motor as one of the company，Domestic application scope is less，But the product quality is excellent，Formal usage andSEW
2015-05-06 Reading quantity 2862
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
