Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction：The impeller mouth ring of polyimide carbon fiber composite material is matched with the pump shell mouth ring of stainless steel；Replace the graphite bushing with the throat bushing of our material。The vibration amplitude is reduced，This extends the service life of seals and bearings[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Service life，Enhance the free operation of the pump。Many pumps are in use with
2015-01-05 Reading quantity 1529
introduction：INAbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]At slightly negative operating clearance，Single bearing life maximum。But it is actually very difficult to keep the bearings in this optimum state once certain conditions of use change，The negative clearance increases，Resulting in a significant reduction in bearing life or heat。therefore，The initial clearance is usually chosen，
2015-01-05 Reading quantity 1537
introduction：Planetary reducer in the run-in period has some common problems，Including loosening、wear、leakage，The main reason for these problems is that the device performance is not familiar enough，New equipment assembly gap is too small。For the main unit situation general in the following one by one analysis： copyright by ：www.tyreducer.com 1、Operation error：Due to the structure of the gear motor、Performance is not well understood，Easy to cause faults due to misoperation，Even cause mechanical accidents and safety accidents。 2、loosen：Newly machined and assembled parts，
2015-01-05 Reading quantity 2883
introduction：Method for surface pretreatment of rustproof substance： 1)Surface cleaning：Cleaning must depend on the nature of the surface of the rust-proof substance and the conditions at the time，Select the appropriate method。Solvent cleaning method is commonly used、Chemical cleaning and mechanical cleaning。 2）The surface can be dried with filtered dry compressed air after cleaning，Or use120~170℃The dryer is used to dry，Can also be dried with clean gauze。 Method of applying anti-rust oil 1）Soaking method：Some small items are soaked in rust-proof grease，A method of affixing a layer of anti-rust grease to its surface。Oil film thickness can be controlled to prevent rust
2015-01-05 Reading quantity 1456
introduction：Rolling bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]It is a high precision mechanical component，Its internal and surface quality requirements are very strict，Therefore, the contact of the inventory must be kept well，Avoid bearing damage during inventory without use，Reduced accuracy or quality。 The main reasons for the loss of bearing stock are as follows： 1)
2015-01-05 Reading quantity 1539
introduction： hole (Hole) Opening holes on plastic parts to make them join with other parts or increase the combination of product functions is a common technique，The size and position of the holes should not affect the strength of the product or increase the complexity of production，Here are a few factors to consider when designing a hole。 The distance between the connecting hole or the hole and the straight edge of the adjacent product shall not be less than the diameter of the hole，For example, a drawing of a hole from an edge or an inner wall edge。At the same time，The wall thickness of the hole should be as large as possible，Otherwise, the perforation position is prone to fracture。If there is a thread in the hole，The design requirement is
2015-01-05 Reading quantity 2881
introduction：Superfinishing can generally be divided into three stages：Cutting stage、Half-cut stage、Finishing stage。 （1）Cutting stage When the surface of the grinding stone is in contact with the convex peak of the surface of the rough raceway，Due to the small contact area，{TodayHot}The pressure per unit area is greater，Under certain pressure，The millstone is first affected by the workpiece“Reverse cutting”effect，Some of the abrasive particles on the surface of the grinding stone fall off and break，Revealing some new sharp grates and edges。At the same time，The convex peaks on the workpiece surface are subjected to rapid cutting，The convex peaks and grinding metamorphic layers on the workpiece surface are removed by cutting and reverse cutting。This stage
2015-01-05 Reading quantity 1447
introduction：1、Theoretical knowledge is improving day by day，Closer to reality（Such as gear strength calculation method、Modification technique、Deformation calculation、Optimal design method、Root smooth transition、New structure）。 2、Use good materials，Various high quality alloy steel forgings are widely used，Improved quality control of materials and heat treatment。 3、The structure design is more reasonable。 4、Machining accuracy improved toISO5－6level。 5、bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said
2015-01-05 Reading quantity 2893
introduction：With the development of the automobile industry，Manufacturers to reduce the weight of the car、Improve performance，And increase the flexibility of the design，Growing preference for plastic parts。Interior trim from the door、Instrument board，To engine components and hood, etc，General passenger car plastic parts have now accounted for all parts10％around。As a key link affecting the performance of plastic parts，The choice and use of lubricants is very important。 Lubricants reduce friction，To reduce wear、noise。Such as，Use lubricant on plastic gears or sliders，Can reduce noise；Many of the plastics used in door panels require lubrication，Including guide、Sliders and rollers、
2015-01-05 Reading quantity 2799
introduction：ifINAbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Iron filings inside、burr、Foreign bodies such as dust enter，The rolling bearing will produce noise and vibration during operation，It can even damage raceways and rolling elements。therefore，Before installing bearings，You must ensure that the installation surface and installation environment are clean。 Lubricating pairINABearing operation and
2015-01-05 Reading quantity 1553
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
