Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： To maintain it in good condition for as long as possibleINAbearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]Inherent performance，Must be maintained、overhaul、To prevent accidents before they happen，Ensure the reliability of operation，Increase productivity、economy。Maintain the best corresponding machinery
2015-01-05 Reading quantity 1546
introduction： Working principle Material powder particle，In raw material container（Fluidized bed）In the annular fluid state，Be preheated and mixed by purified heated air，Spray in the adhesive solution，To aggregate several particles into a mass containing a binder，Due to the continuous drying of materials by hot air，Evaporates the water in the aggregates，Adhesive setting，This process is repeated over and over，idealize、Uniform multi-microporous spherical particles。 ,&nb
2015-01-05 Reading quantity 2809
introduction：NSKbearing[NSKbearing:Seiko Co., LTD（NSK LTD.）Be established in1916years，It is the first manufacturer to design and produce bearings in Japan。NSKThe function of the bearing fit is to makeNSKThe stationary ring and rotating ring of the bearing are respectively the stationary part of the installation part(Usually a bearing seat)And rotating part(Usually an axis)Solidify together，Thus, the basic tasks of transferring the load in the rotating state and defining the position of the moving system relative to the stationary system are realized。]post-installation，Causes of bearing rotation difficulties NSKbearing[NSKbearing:Seiko Co., LTD（NSK L
2015-01-05 Reading quantity 1455
introduction：Mold is the main process equipment of industrial production。The development of modern industrial products and the improvement of technical level，To a large extent depends on the development level of the mold industry。Since World War II，The improvement of the degree of automation makes the rapid development of foreign molds。Although China is a large country of mold production,But it is not a mold manufacturing power。To match the spring to the mold，This detail is also the key to quality。Affect the performance of the whole mold。 I am engaged in surface treatment engineering specialty，The surface treatment of die spring, that is, rectangular spring, is investigated。Find the following problem，Bring up for discussion。
2015-01-05 Reading quantity 2808
introduction：Definition of plastic Plastic refers to resin（Or directly polymerized with monomers during processing）Be the main component，To plasticizer、filler、lubricant，Additives such as colorants are auxiliary ingredients，Materials that can flow and form during processing。Plastics mainly have the following characteristics：①Most plastics are light，Good chemical stability，non-rusting；②Good impact resistance；③It has good transparency and abrasion resistance；④Good insulation，Low thermal conductivity；⑤General formability、chromaticity，Low processing cost；⑥Most plastics have poor heat resistance，High thermal expansion rate，combustible；⑦Poor dimensional stability，Easily deformed；⑧Most plastics are resistant to low temperatures
2015-01-05 Reading quantity 2873
introduction： 1、If the microscope is not equipped with a light source，The microscope can be placed on a smooth table，Facing the wide window（If the light is bad，Incandescent lamp or fluorescent lamp can be used as light source）； 2、Turn the low power objective right under the tube，Make it about distance from the loading stage1centimetre。And raise the condenser to full height，Put the aperture to the maximum，And then one side looks through the eyepiece，A rotating mirror，Make the light from the source reflect as much as possible to the condenser（If the microscope is equipped with a light source，This step can be omitted）； 3、
2015-01-05 Reading quantity 2888
introduction： The clutch is an important part of the machine，Proper operation can avoid damage to the clutch，At the same time, it can also make the owner enjoy a more comfortable driving experience。What are the correct operation steps of the clutch?Feng Ye mall to take you to have a look。 The operation essentials of the correct use of the clutch pedal when driving a car are“prompt、Two slow conditions、Triple linkage”。That is, at the beginning of the pedal lift fast;When the clutch appears half linkage，The pedal is lifted slightly slower;The process from linkage to complete combination，Lift the pedal slowly;With the clutch pedal lifted，Gradually depending on the engine resistance
2015-01-05 Reading quantity 2908
introduction：advantage： 1.Pure liquid friction，Low friction resistance，Low power consumption，High transmission efficiency。 2.Normal operation and frequent start-up，There is no wear caused by direct contact between metals，Good accuracy retention，Long life。 3.Because the lifting of the axle diameter is achieved by the pressure of external oil，therefore，At all relative speeds，All have high carrying capacity，The change of velocity has little effect on the stiffness of oil film。 4.The lubricating oil layer has good vibration resistance，Shaft running smoothly。 5.The oil film has the function of compensating the error，Can reduce shaft and bearing[bearing:bearing（“Beari
2015-01-05 Reading quantity 1548
introduction： Stamping deformation process can complete a variety of processes，The basic process can be divided into two categories: separation process and deformation process。 The separation process is the process of separating one part of the embryo from another，There are mainly blanking materials、punching、trimming、sectioning、trimming。Which is also punched、Blanking is the most widely used。Deformation process is to make one part of the embryo relative to another part of the displacement without breaking the process method，It mainly involves deep drawing、bend、Local forming、bulging、Turning edge、Drawing down、sizing、spinning。 In essence，Stamping is the deformation of the wool embryo
2015-01-05 Reading quantity 1460
introduction：inKOYOBearing during use，It can be said that vibration and temperature on the bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The impact is very large，Lets first look at the impact of bearing vibration on external spherical bearings。 Vibration can be said to be quite sensitive to bearing damage，Peel off、impression、corrosion、crack、Wear and tear will be on the shaft
2015-01-05 Reading quantity 1553
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
