Batch Smart quick quote，
Export quotation with one click，
One-click order
Monday to Saturday8:30-18:00
introduction： bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]When mounted on the rotor to do dynamic balancing, it is easy to enter the iron filings generated during dynamic balancing into the bearing，So its best to pretendTIMKENDo dynamic balancing before bearing。There are some manufacturers for the convenience of assembly，Apply one to the bearing chamber during assembly
2015-01-01 Reading quantity 1557
introduction： Main use： This machine is suitable for pharmaceutical、Chemical engineering、metallurgy、food、Construction and other industries。convexity、Difficult to crush the material processing，Inclusive plastic、Copper wire etc. are crushed，It can also be processed as a micro-pulverized material，Inclusive plastic、Copper wire etc. are crushed，It can also be used as a supporting equipment for the previous process of micro-grinding processing。 peculiarity： The machine is a vertical grinding mechanism，Not subject to boring viscosity、hardness、Limitations of softness, etc，It can have a better crushing effect on any material。 Working principle： The material is sent to the crushing chamber by the hopper，Through the blade and base
2015-01-01 Reading quantity 2820
introduction：1、Comply with general operating procedures for moulding machines and core machines。 2、pre-work，Check the amount of oil in the large and small cylinders，If the oil is not enough，Refueling should be timely。 3、In the production process，The core sand around the sleeper should be removed regularly，To keep the sand from burying the vents，Causing sand to enter the cylinder。 4、In the production process，The sand deposits on the contact surface between the shaking table and the turning table should be removed regularly。 5、preflip，The box must be locked securely；No one should stand near the front of the device when flipping，To avoid personal accidents。 6、In the production process，If the core is often damaged during demoulding，Should check the turn
2015-01-01 Reading quantity 2813
introduction： 1、Process flow：Steel wire、Bar stock——>laying-off——>pommel/chamfering——>Heat treatment——>grinding——>package Type code（It is represented by numbers or letters）As shown in the table below： designation bearing[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission
2015-01-01 Reading quantity 1465
introduction：yasuoshi zhilengji Compression refrigerator compression refrigerating machine A refrigerator that relies on a compressor to increase the pressure of the refrigerant to achieve a refrigeration cycle。Compression chiller by compressor、condenser（condenser）、Refrigeration heat exchanger（evaporator）、Expansion machine or throttle mechanism and some auxiliary equipment。Compressor is its core equipment。 Classification varies according to the type of refrigerant used，Compression refrigerator is divided into gas compression refrigerator and vapor compression system
2014-12-31 Reading quantity 2835
introduction：The silver linear slide is a rolling guide，An infinite rolling cycle between the slider and the rail is performed by the steel ball，The load platform can easily move linearly along the slide rail with high precision。?
2014-12-31 Reading quantity 32153
introduction：Powder metallurgy terms can be classified under the following main headings： powder shaping sintering Post-sintering treatment Powder metallurgy material Here are some commonly used terms for powder metallurgy，Mainly extracted fromGB/T 3500-1998 《Terminology of powder metallurgy》 ，I hope it was helpful。 one、powder： powder powder Usually means less than1mmAn aggregate of discrete particles。 starch slurry A pourable viscous dispersion system of powder in a liquid。 preform feedstock
2014-12-31 Reading quantity 2818
introduction： The use factor mainly refers to the installation adjustment、Service and maintenance、Whether the maintenance and repair meet the technical requirements。On the basis ofKOYOBearing mounting、Use、maintenance、Technical requirements for maintenance，For bearings in operation[bearing:bearing（“Bearing”，Japanese person“Axial receptor”）It is a part that holds and reduces the friction coefficient of load during mechanical transmission。Can also be said，When other parts move relative to each other on the shaft，A device used to reduce the coefficient of friction during power transmission and to keep the center of the shaft fixed。]The load borne、Rotational speed、professional
2014-12-31 Reading quantity 1570
introduction：⒈Tire selection and installation Whether the tire is installed correctly or not is directly related to the service life of the tire，Especially when it comes to new tires。Different tire types and patterns，Due to the actual size and load capacity of each tire is different，Must not be arbitrarily mixed。In addition，If you cant fully master the skill of changing a tire yourself，We recommend that you still go to a professional tire shop or vehicle maintenance office to replace。 ⒉Working pressure Tire pressure is too low or too high，Will affect the service life of the tire。If the tire pressure is too low，Its radial deformation increases，Tread wall
2014-12-31 Reading quantity 1563
introduction：Surface finish grade、Features and uses Primary surface：NO.1A surface treated with heat treatment and pickling after hot rolling。Generally used for cold rolling materials，Industrial tank、Chemical industrial plant, etc，Thicker by2.0MM-8.0MM。 Blunt surface：NO.2DHeat treatment after cold rolling、pickler，Its material is soft.，The surface is silver-white gloss，For deep stamping，Such as car parts、Water pipe。 Fog level：NO.2BHeat treatment after cold rolling、pickling，Then finishing to make the surface for a moderate brightness。On account of
2014-12-31 Reading quantity 1567
Complete category
Save worry and effort，Buy all at one stop
One-to-one customer service
Selection inquiry，Fast response
Delivery guarantee
Multi-position straight hair，No worries about delivery
Source of genuine goods
Genuine guarantee，Honest service
Source of genuine goods
Genuine guarantee，Honest service
Automatic parts one-stop procurement platform
Working hours：Monday to Saturday 8:30-18:00
008618117444109
Official wechat public account
Order for goods/Information at hand
